产品名称 : SLBS05 Chlorinated Rubber Coat

特征

PRODUCT NAME Chlorinated Rubber Coat SLBS05
BRIEF Primer intermediate finishing coating made from epoxy resin, acrylic acid resin, aliphatic polyurethane resin, pigments and extenders, function materials, modifier, etc
FEATURES
-Excellent ageing resistance
-Excellent resistance to pulverization and crack
-Use for a long time not yellowing
-Excellent heat insulation property
-Excellent reflecting sunlight
RESISTANCE GUIDE
HEAT RESISTANCE       Up to 120℃ dry heat
WEATHERABILITY        Excellent gloss and colour retention when exposed
SOLVENTS              Resists splash and spillage of aliphatic solvent, mineral oil
ACIDS                 Suitable for splash and spillage to most acids
ALKALIS               Suitable for splash and spillage to most alkalis
SALTS                 Excellent resistance to neutral and alkali salts
WATER                 Excellent resistance to fresh and salt water, but not suitable for soaking
ABRASION              Good when fully cured.
USES: Widely on all kinds of pressure containers as PLG spherical tank, oil tanker, chemical pipeline equipment, chemical raw material tank, refrigerated trucks, external surface of the steel structure workshop, warehouse, etc, serve as heat insulation and cooling.
TYPICAL PROPERTIES AND APPLICATION DATA
Primer(glue)         Intermediate(glue) Topcoat(glue)
COLOR B              Brown Red Light Grey /White White
DENSITY              1.4g/cm3  1.4g/cm3     1.2g/cm3
SOLIDS BY VOLUME     56%       56%          42%
SOLIDS BY WEIGHT     76%       76%          72%
SPREADING RATE 5.0 m2/kg(80um DFT) 5.0 m2/kg(80um DFT) 6.7 m2/kg(50um DFT)
DRYING TIME(23℃)    Touch 4 Hr Handle 24 Hr
OVERCOAT INTERVAL(23℃) Min 8 Hr Max 7 Days
STORAGE              at least 12 months (dry, cool and under cover )
PACKAGING            Primer Part A: 21kg Part B: 3kg
Intermediate         Part A: 21kg Part B: 3kg
Topcoat Part A: 20kg Part B: 4kg
DIRECTIONS Primer(glue), Intermediate(glue), Topcoat(glue) is a two pack, before using stir or using dynamic mixer mixing two components completely, then add part B to part A, and fully stir, life for 4 hours. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir. Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be added after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.

APPLICATION

STEEL: The surface coated by primer or intermediate paint should be dry and clean, no oil and other pollutants. When overcoat on a two-component film such as epoxy paint, wharf's pavement quality for old film should be taken if more than the longest accordance with time.
Don’t apply at temperatures below 5℃ or above 40℃. Don’t apply at relative
humidity above 85% or when the surface is less than 3℃ above the dew point. Don’t apply if there is fog, rain, snow or strong wind.
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Special Thinner(Primer, Intermediate X-2, Topcoat X-5). Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Special Thinner(Primer, Intermediate X-2, Topcoat X-5) can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Special Thinner(Primer, Intermediate X-2, Topcoat X-5) can be added. Pump ratio is 23:1 or 32:1 and fluid tip is 0.33-0.38mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
CLEAN UP: Special Thinner (Primer, Intermediate X-2, Topcoat X-5)

SAFETY: Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.